Samsung Dishwasher Error Codes: What They Mean
Updated 2026-11-05
If your Samsung dishwasher is flashing an error code, the exact code will vary by model and control panel generation — but on most Samsung dishwashers, fault codes fall into a handful of general categories: water fill, drainage, the heating element, door sensing (including the AutoRelease door on newer models), and the electronic control board. Here's how to read what your Samsung is telling you, what typically causes it, and when it's worth calling a technician instead of troubleshooting further yourself.
Water fill
The dishwasher isn't detecting the expected water level, or the inlet valve isn't filling the tub correctly.
Common causes:
- A kinked or partially closed water supply line
- A clogged inlet valve screen or filter
- A failed float switch or water level sensor
Confirm the shutoff valve under the sink is fully open, and check that the float switch at the front of the tub moves freely and isn't trapped under a dish or utensil. If supply and float both check out, the inlet valve or sensor needs a technician's diagnosis.
Drain / flow
The dishwasher isn't draining or circulating water as expected, or water is left standing in the bottom of the tub.
Common causes:
- A clogged filter assembly at the bottom of the tub
- A kinked or blocked drain hose
- A failing drain pump or check valve
Remove and rinse the coarse and fine filter assembly at the bottom of the tub — this is the single most common cause of drainage errors and is safe to check yourself. If the filters are clean and the hose isn't kinked, the drain pump likely needs replacing.
Heating element / thermistor
The heating element isn't reaching temperature, or the thermistor reading is out of the expected range — this affects both wash performance and the dry cycle.
Common causes:
- A burned-out heating element
- A failed thermistor or temperature sensor
- The control board not sending power to the element
There is no reliably homeowner-safe check here — the element carries line voltage and sits in a wet compartment. Any heating-related code is worth a technician's diagnosis rather than DIY testing.
Door / latch / AutoRelease
The control board isn't confirming a secure, sealed door close — or, on newer models, isn't confirming that the automatic venting door has closed again after opening.
Common causes:
- A worn or misaligned door gasket
- A failed door latch or door switch
- On DW80 and newer Samsung models with an AutoRelease door, a mechanism that isn't releasing or re-latching correctly
Many current Samsung dishwashers skip a heated dry element altogether and instead crack the door open automatically near the end of the cycle to vent steam and air-dry the dishes. If that AutoRelease mechanism doesn't release on schedule or fails to latch again for the next cycle, the control board can read it as a door fault. Inspect the gasket for gaps or tears and confirm the door latches without extra force; if everything looks fine but the fault persists, the AutoRelease motor or door switch needs a technician's diagnosis.
Electronic control board
The main control board is reporting an internal fault rather than a specific component failure.
Common causes:
- A power surge or brownout that affected the board
- A failing relay or component on the board itself
- A wiring fault feeding it an incorrect signal from another part
Unplug the dishwasher (or switch off its breaker) for 60 seconds before restoring power — this clears a one-off glitch on many models. If the code returns immediately, the board itself needs professional diagnosis.
Why we don't list exact codes here
Samsung has used several different control panel and display generations across its dishwasher lineup — from older models with simple LED indicator lights to current touch-panel and Wi-Fi-connected models that display a specific alphanumeric code. The same displayed code doesn't always mean the same thing across every series. Check your model's manual for the exact code list, or call us and we can confirm it over the phone before booking a visit.
Safety note: Dishwashers combine water and mains-voltage electrical components in a tight space. Beyond checking the filter assembly and door gasket, leave heating element, AutoRelease mechanism, and control board diagnosis to a certified technician.
Have this exact problem? Our certified technicians repair this appliance , with same-day availability in most cases.
See our Samsung appliance repair page for full service details.
Request a Service Call Estimate